bolts? to mount sbc 350 on an engine stand - Team Chevelle
2006年5月23日 · The bolts are 3/8"-16 but the length depends on how thick the four engine stand "arms" are. Could be 2 to 3" long. I recommend buying washers (thick if possible) also for these bolts.
Big block engine stand bolts. - Team Chevelle
2004年6月28日 · Read this and you will never worry about 3/8's grade 5 bolts holding a a mear engine block again. I think everyone should educate them selfs on bolts, I can tell by everyones answers about 5 VS 8 just to hold a block on a stand that everyones just quessing, considering a grade 5 .250 bolt take over 3600 lbs of force to shear it.
what size bolts to mount small block onto stand?
2008年2月7日 · I dont want to point out the obvious, but make sure you get at least grade 5 bolts grade 8 would probably be overkill, but its your feet under that motor. First motor I tried putting on a stand (16 years old at the time) I got some generic farmer bolts. Fortunately it was still hooked to the hoist when the bolts snapped. Jim
Engine stand bolt size - Team Chevelle
2007年12月7日 · I used Grade 8 bolts on a 1200 lb capacity stand just last week...and the bolts worked great. It was the stand that bent to hell. I lowered the BB off the chain and the stand just kept bending and bending. I bought a nice little 1000 lb engine cradle for $30 on e-bay and it …
Mounting BBC on engine stand. - Team Chevelle
2009年6月22日 · The stuff sold at most stores is chinese grade 0 junk. You can put a nut on it and just keep tightening until it breaks. Grade 3 isn't something I would use to hold an engine on a stand. Grade 5 minimum! I also never scrimp on my engine stands. My engines cost too much to leave to chance.
Broken bolt in engine stand? - Team Chevelle
2014年3月27日 · I have had a Bigblock hanging in an engine stand using four 3/8 unc grade 5 bolts. To make it stronger I decided to use 4 inches long grade 8 studs and nuts instead. Last night when I just rolled the engine/engine stand on the floor one stud broke off just in front of the nut. The nut with the broken piece of stud in it fell to the floor.
Engine Stand - Team Chevelle
2019年12月18日 · This is achieved by the "V" shaped legs and helped if the engine is a bit difficult to turn due to friction in the head stock . Use a little grease and a piece of 2ft tube tube makes shifting easier . Bonus is u can use them as an engine run stand as well with xtra support legs placed on engine mounts .
Engine stand - Team Chevelle
2014年1月9日 · The bolts that go into the back of the block are the same size as those that would hold the bell housing and transmission. They go in about 7/8 of an inch into the back of the block before they bottom out. I can only use four of them since there are only four engine stand brackets. Is that enough to hold that engine up ?
engine test stand wiring - Team Chevelle
2013年8月8日 · The plate that the bellhousing bolts to removes and bolts back on in a folded position, then i stand the unit up. The biggest headache is the radiator support. It too comes off and can stand/lean against the dolly part, but the gauge pod is a total cluster and a true pain, even though I made that so it comes off too, but it contains the most ...
Engine Cradle / Engine Stand Question - Picture - Team Chevelle
2009年6月15日 · just make sure you unbolt the toque converter bolts and push the converter away from the flexplate while the motor/trans is still in the car- it's easier that way. when you get the assembly out of the engine bay, set it down on the ground with the picker holding enough of the weight to balance it, unbolt the trans, and bolt the engine into the ...
- 某些结果已被删除