Purple glue stick (Page 1) — Solidoodle Discussion - SoliForum
2015年7月6日 · Re: Purple glue stick Offcourse,,, i ment, to much will be lost in transaction trough the tape , I havens fot the printer yet, just prepering all i can to then it is ariving :-) 19 Reply by Don9mm 2014-09-25 01:24:05
ABS Juice (blows away purple glue stick) (Page 1) - SoliForum
2015年7月8日 · Re: ABS Juice (blows away purple glue stick) I've used both (ABS paste on an Ultimaker 2, UHU stick (the stuff that comes with the printer) and hair spray. In my experience, the UHU stick works exceptionally well with ABS, while …
Alternative to Glue Stick (Page 1) - SoliForum
2015年1月15日 · And blue tape with glue stick for large planar surfaces (also brims help). For pla I use blue tape with airspray for planar surfaces or just 50-60C with glue stick for less stressfull surfaces. For PLA you should just be able to use hot dry and bare glass. If …
PETG and glue sticks (Page 1) — 3D Printer Discussion - SoliForum
2017年9月20日 · Scotch® Purple Glue Sticks 6108-2N, 0.25 oz. 2/ pack - strong, fast-bonding, permanent adhesive, and safe for children. You can see where you apply it, but it dries clear. Hands and household surfaces clean easily with soap and water. Great for paper, photos, and other lightweight items.
ABS Questions (Page 1) — XYZ Printing DaVinci - SoliForum
2015年11月28日 · carl_m1968 wrote: The glue sticks are used on glass or kapton tape over a heated bed for abs. The painters tape is used alone on the metal or over glass on a room temp bed not heated for pla. Although you can heat the bed for pla but it should not be needed if leveled correctly. Never ever print directly to metal.
Glue stick? (Page 1) — XYZ Printing DaVinci - SoliForum
2018年2月6日 · The idea with the glue stick is that when it is over 55degC, it bonds the ABS to the heated bed. You can skip using the glue stick if: 1 - you have calibrated your filament's optimum printing temperature, along with heatbed temperature. 2 - If you have good quality dry abs. In most other cases, apply a thin layer to the cold bed, and that ...
Prints not sticking to bed (Page 1) - SoliForum
2018年5月29日 · I was having a lot of trouble with prints not sticking as well (only tried .1 with glue). It could be that the bed needs recalibrating. I spent 1-2 hours doing the calibration over and over until it was close and finally said "SUCCESS". It was dragging plastic all over the place on the keychain demo before and printed just fine afterwards.
GlueStick Vs Kapton Tape vs both glue and Kapton (Page 1) — …
2015年2月9日 · When I got my DaVanci 1.0, I use the UHU stick that came with it and then started using purple elmers gluesticks since then. I recently purchased a 100ft roll of 200mm kapton tape and finally figured out a good method for putting it on. It hold really well, in fact sometimes too well.
Re-using rafts? (Page 1) — Solidoodle Discussion - SoliForum
2016年1月29日 · Another trick you could try to get away from rafts would be putting Elmers purple glue stick on the area to be printed in on the purple tape. As long as the object stay warm the tape and glue should hold it down. Printing since 2009 and …
Preventing warp with ABS (Page 1) — Solidoodle Press - SoliForum
2015年2月7日 · This thread is missing the best solution, IMO: purple glue stick. It coat of purple glue stick has been all I need to print a large object the size of the entire bed and with sharp corners with no warping. It's also much less messy than hairspray and doesn't get all over your rods. I use it on every print.