3 different thrust washers! which one to use!?? - iboats Boating …
2008年3月6日 · The MIDDLE washer is the assumed factory thrust washer that is thicker than the new waser and still has a beveled edge. Will NOT work on current gearcase. the Washer on the Right is the currently installed Lower gearcase. It has NO BEVEL cut into the inside and NEITHER DOES the installed gearcase on the output shaft. Its absolutly huge.
Thrust washer problem | Boating Forum - iboats Boating Forums
2018年6月12日 · I slowely went through the manual again, it’s part number 33 the upper thrust washer, it has a taper which is mentioned in the manual as does the one I have randomely, and it has the marks from the bearing that gets sandwiched between the lower thrust washer, it also has wear from tip of drive shaft ... some how this washer came out when I pulled the drive shaft out …
Thrust washer stuck | Boating Forum - iboats Boating Forums
2012年3月14日 · Re: Thrust washer stuck I combined all methods, minus the puller. I heated up the joint itself, and I noticed it was pushing some of the corrosion out. I kept heating it and kept prying lightly from behind with a flathead. Then after fit was hot, I would hit is with a plastic mallet opposite of the screwdriver. Spin a little, repeat.
Thrust washer removal | Boating Forum - iboats Boating Forums
2005年3月29日 · Re: Thrust washer removal Thanks guys, a little WD-40, pry bar, and 5 taps from a hammer was all it took. The washer looks fine but I'm gonna change it just to be safe. I would'nt want to damage my new Stiletto 4 blade.
Thrust washer and spacer? - iboats Boating Forums
2010年7月8日 · Re: Thrust washer and spacer? Thanks to everyone for excellent info. Yes the old washer was indeed the old thrust washer. It has a taper bore with p/n 752852 which is the correct number according to iboats. Anyway it was easy to tap off and replace with new. Same thickness as old; now everything looks much better after installation.
Thrust washer issue | Boating Forum - iboats Boating Forums
2021年9月13日 · The new forward thrust washer from the hub kit, however, will not slide all the way to the base of the prop shaft, stopping with about 1.5 inches to go. The slots look slightly tighter than the ones on the old thrust washer, but the info I got from the manufacturer website, as well as the marine part store I bought it indicates I have the ...
Do I need thrust washer for new prop? - Boating Forum
'91 115 mercury 2 stroke/ 13x19 pitch. prop is quicksiler. Want to order new stiletto ss 13x19 prop but instructions say I need new thrust washer.
Should thrust washer recess into the prop? - Boating Forum
2006年5月4日 · With some of them they indicate that you need a different thrust washer. Possibly the different washer is a different thickness (I don't know) which would solve your problem. Why don't you just contact them with your question and see what they have to say.<br /><br />Don't know that I'd glob a bunch of stuff on the prop shaft that wasn't ...
Tohatsu thrust washer | Boating Forum - iboats Boating Forums
2023年10月11日 · Tohatsu thrust washer. Thread starter Scottkirkman1; Start date Oct 11, 2023; S. Scottkirkman1 Cadet ...
Tohatsu Prop Thrust Washer - iboats Boating Forums
2011年8月12日 · Re: Tohatsu Prop Thrust Washer Guru, thanks for your advice. My first post may not have been clear. The part I am calling a thrust washer is identified as a "propellor thrust holder" in my owner's manual. It is forward of the prop, i.e. toward the bow of the boat. The thrust washer is stuck to the shaft, not to the prop itself.